| |
Brodit ProClip for Fiat Marea - Center mount
Stock : 1 - 3 [ call to confirm ]
|
Item No. : 652224 for Years 97-07 in UK |
|
|
|
The images show the mounting position for the Brodit ProClip for your Fiat Marea. Onto this you can then attach the Brodit Active or Brodit Passive Holder as shown in the video.
|
|
The ProClip is a mounting bracket for the Fiat Marea's dashboard. Onto the Proclip you can install e.g. a holder for your mobile phone or PDA or a handsfree set etc. Safe and convenient -always within easy reach. The ProClip is car specific and easy to install. The installation is quick, no special tools or dismantle of the dashboard is required and it will not damage the interior of the Fiat Marea. Made in black ABS plastic. Comes with detailed instructions.
Whether mounted on the console or on the dashboard, the ProClip car kit affords you the ability to install these car kit mounts using no special tools or dismantling of the dashboard. The designs of these mounts are made to cradle any device while tested to fit perfectly in the vehicles listed. These hard ABS plastic units hold your PDA, Mobile or GPS unit allowing you to run down the most pitted city streets without the fear of your device falling out of the cradle and rolling around the floorboards. Other customers have purchased other equipment (sold separately) used with the kits which includes additional mounting equipment, multimedia equipment, charging cables and handsfree kits. Other attachments (sold separately) also include Trion's Maxi Mute, VDA Cables, Water Resistant Cases and Voltage Converters.
|
|
|
|
|
|
| |
Brodit ProClip for Fiat Marea - Angled mount
Stock : 1 - 3 [ call to confirm ]
|
Item No. : 652781 for Years 97-07 in UK |
|
|
|
The images show the mounting position for the Brodit ProClip for your Fiat Marea. Onto this you can then attach the Brodit Active or Brodit Passive Holder as shown in the video.
|
|
The ProClip is a mounting bracket for the Fiat Marea's dashboard. Onto the Proclip you can install e.g. a holder for your mobile phone or PDA or a handsfree set etc. Safe and convenient -always within easy reach. The ProClip is car specific and easy to install. The installation is quick, no special tools or dismantle of the dashboard is required and it will not damage the interior of the Fiat Marea. Made in black ABS plastic. Comes with detailed instructions.
Whether mounted on the console or on the dashboard, the ProClip car kit affords you the ability to install these car kit mounts using no special tools or dismantling of the dashboard. The designs of these mounts are made to cradle any device while tested to fit perfectly in the vehicles listed. These hard ABS plastic units hold your PDA, Mobile or GPS unit allowing you to run down the most pitted city streets without the fear of your device falling out of the cradle and rolling around the floorboards. Other customers have purchased other equipment (sold separately) used with the kits which includes additional mounting equipment, multimedia equipment, charging cables and handsfree kits. Other attachments (sold separately) also include Trion's Maxi Mute, VDA Cables, Water Resistant Cases and Voltage Converters.
|
|
|
|
|
|
| |
Brodit ProClip for Fiat Marea - Center mount
Stock : 1 - 3 [ call to confirm ]
|
Item No. : 852224 for Years 97-07 in Europe |
|
|
|
The images show the mounting position for the Brodit ProClip for your Fiat Marea. Onto this you can then attach the Brodit Active or Brodit Passive Holder as shown in the video.
|
|
The ProClip is a mounting bracket for the Fiat Marea's dashboard. Onto the ProClip you can install e.g. a holder for your mobile phone or PDA or a handsfree set etc. Safe and convenient -always within easy reach. The ProClip is car specific and easy to install. The installation is quick, no special tools or dismantle of the dashboard is required and it will not damage the interior of the Fiat Marea. Made in black ABS plastic. Comes with detailed instructions.
Whether mounted on the console or on the dashboard, the ProClip car kit affords you the ability to install these car kit mounts using no special tools or dismantling of the dashboard. The designs of these mounts are made to cradle any device while tested to fit perfectly in the vehicles listed. These hard ABS plastic units hold your PDA, Mobile or GPS unit allowing you to run down the most pitted city streets without the fear of your device falling out of the cradle and rolling around the floorboards. Other customers have purchased other equipment (sold separately) used with the kits which includes additional mounting equipment, multimedia equipment, charging cables and handsfree kits. Other attachments (sold separately) also include Trion's Maxi Mute, VDA Cables, Water Resistant Cases and Voltage Converters.
|
|
|
|
|
|
| |
Brodit ProClip for Fiat Marea - Angled mount
Stock : 1 - 3 [ call to confirm ]
|
Item No. : 852781 for Years 97-07 in Europe |
|
|
|
The images show the mounting position for the Brodit ProClip for your Fiat Marea. Onto this you can then attach the Brodit Active or Brodit Passive Holder as shown in the video.
|
|
The ProClip is a mounting bracket for the Fiat Marea's dashboard. Onto the ProClip you can install e.g. a holder for your mobile phone or PDA or a handsfree set etc. Safe and convenient -always within easy reach. The ProClip is car specific and easy to install. The installation is quick, no special tools or dismantle of the dashboard is required and it will not damage the interior of the Fiat Marea. Made in black ABS plastic. Comes with detailed instructions.
Whether mounted on the console or on the dashboard, the ProClip car kit affords you the ability to install these car kit mounts using no special tools or dismantling of the dashboard. The designs of these mounts are made to cradle any device while tested to fit perfectly in the vehicles listed. These hard ABS plastic units hold your PDA, Mobile or GPS unit allowing you to run down the most pitted city streets without the fear of your device falling out of the cradle and rolling around the floorboards. Other customers have purchased other equipment (sold separately) used with the kits which includes additional mounting equipment, multimedia equipment, charging cables and handsfree kits. Other attachments (sold separately) also include Trion's Maxi Mute, VDA Cables, Water Resistant Cases and Voltage Converters.
|
|
|
|
|
|
| |
Brodit ProClip for Fiat Marea - Headrest mount
Stock : Brodit Brand New Item - PreOrder Yours NOW !
|
Item No. : 811030 for Years 97-07 in Europe |
|
|
|
The images show the mounting position for the Brodit Headrest mount for your Fiat Marea. Onto this you can then attach the Brodit Active or Brodit Passive Holder as shown in the video.
|
|
Fits headrests with the following measurements between the bars: Min. inner size 151 mm, Max. outer size 211 mm.
The headrest mount is car specific and serves as a mounting platform. Onto the headrest mount you can attach any holder of your choice, e.g. for a surfpad or a multimedia monitor. Example: If you are installing a surfpad in the car you will need two parts; the correct headrest mount (specific for your car) and the correct holder (specific for your surfpad).
The headrest mount is to be placed onto the front seat's headrest. You can install it yourself in a couple of minutes, installation instructions are included. The headrest mount faceplate has predrilled holes which makes the attachment of a holder easier.
Holders that can be installed onto the headrest mount can be found easily in the device search feature on our website. All Brodit's holders can be attached onto the headrest mount, but some surfpad holders are crashtested and approved for use on Brodit's headrest mounts (look for crash test labeling).
This headrest mount fits a number of Fiat Marea, some of them are listed here. Are you missing a model? Measure the headrest in you Fiat Marea. If the following measurements match, this product will fit in your car.
Minimum inner size between headrest bars: 151 mm
Maximum outer size between headrest bars: 211 mm
|
|
|
|
|
|
| |
Brodit ProClip for Fiat Marea - Headrest mount
Stock : Brodit Brand New Item - PreOrder Yours NOW !
|
Item No. : 811030 for Years 97-07 in UK |
|
|
|
The images show the mounting position for the Brodit Headrest mount for your Fiat Marea. Onto this you can then attach the Brodit Active or Brodit Passive Holder as shown in the video.
|
|
Fits headrests with the following measurements between the bars: Min. inner size 151 mm, Max. outer size 211 mm.
The headrest mount is car specific and serves as a mounting platform. Onto the headrest mount you can attach any holder of your choice, e.g. for a surfpad or a multimedia monitor. Example: If you are installing a surfpad in the car you will need two parts; the correct headrest mount (specific for your car) and the correct holder (specific for your surfpad).
The headrest mount is to be placed onto the front seat's headrest. You can install it yourself in a couple of minutes, installation instructions are included. The headrest mount faceplate has predrilled holes which makes the attachment of a holder easier.
Holders that can be installed onto the headrest mount can be found easily in the device search feature on our website. All Brodit's holders can be attached onto the headrest mount, but some surfpad holders are crashtested and approved for use on Brodit's headrest mounts (look for crash test labeling).
This headrest mount fits a number of Fiat Marea, some of them are listed here. Are you missing a model? Measure the headrest in you Fiat Marea. If the following measurements match, this product will fit in your car.
Minimum inner size between headrest bars: 151 mm
Maximum outer size between headrest bars: 211 mm
|
|
|
|
|
|
HTC Kaiser Passive Holder Tilt Swivel
Stock : 6
Item No. : 848752
£ 24.99 incl. Vat
Click Image to enlarge
With your HTC Kaiser in a passive holder attached onto the dashboard it is always within easy reach -safe and convenient. The holder is mounted onto a tilt swivel so it is adjustable for avoiding light reflection on the screen. It is easy to put the HTC Kaiser in the holder, and to take it out of the holder. You can connect e.g. a charging cable to the HTC Kaiser when it is in the holder.
The device can be placed in the holder in a vertical, closed position or a horizontal, open position -choose which way you want to use your device and then simply turn the holder into desired position! Attach onto ProClip Mounting Platform.
|
|
Ford Focus ProClip Center mount
Stock : 7
Item No. : 652667
£ 15.99 incl. Vat
Click Image to enlarge
The ProClip is a mounting bracket for the Ford Focus's dashboard. Onto the Proclip you can install e.g. a holder for your mobile phone or PDA or a handsfree set etc. Safe and convenient -always within easy reach. The ProClip is car specific and easy to install. The installation is quick, no special tools or dismantle of the dashboard is required and it will not damage the interior of the Ford Focus. Made in black ABS plastic. Comes with detailed instructions.
|
|
Apple iPod Touch 2nd Generation Holder with Pass-Through Connector
Stock : 1 - 3 [ call to confirm ]
Item No. : 847861
£ 45.97 incl. Vat
Click Image to enlarge
Padded.
Holder with pass-through connector. All cables that can be used with the iPod can also be used with the holder, for example a charging cable or an interface cable. When you have attached the cable to the holder it is firmly in place and you do not have connect it manually to the device each time you put the iPod in the holder. (Cable not included)
You can easily take the device with you when leaving the vehicle. The holder is equipped with a tilt swivel so it can be adjusted in order to avoid light reflection on the screen. Attach onto ProClip Mounting Platform.
|
|
HTC HD2 Active Holder Tilt Swivel
Stock : 2
Item No. : 512086
£ 34.98 incl. Vat
Click Image to enlarge
With tilt swivel.
The active holder charges your battery when it is in the holder. The holder is attached onto a tilt swivel and can be adjusted in order to avoid light reflection. Connects to the vehicle's cigarette lighter socket, 12/24 Volt. Attach onto a ProClip Mounting Platform. Can be used with HTC original portable Handsfree.
|
|
Lexus GS 300 ProClip Center mount
Stock : 3
Item No. : 652540
£ 15.99 incl. Vat
Click Image to enlarge
The ProClip is a mounting bracket for the Lexus GS 300's dashboard. Onto the Proclip you can install e.g. a holder for your mobile phone or PDA or a handsfree set etc. Safe and convenient -always within easy reach. The ProClip is car specific and easy to install. The installation is quick, no special tools or dismantle of the dashboard is required and it will not damage the interior of the Lexus GS 300. Made in black ABS plastic. Comes with detailed instructions.
|
|
HTC HD2 Passive Holder Tilt Swivel
Stock : 3
Item No. : 511086
£ 24.99 incl. Vat
Click Image to enlarge
With your HTC HD2 in a passive holder attached onto the dashboard it is always within easy reach -safe and convenient. The holder is mounted onto a tilt swivel so it is adjustable for avoiding light reflection on the screen. It is easy to put the HTC HD2 in the holder, and to take it out of the holder. You can connect e.g. a charging cable to the HTC HD2 when it is in the holder. Attach onto ProClip Mounting Platform.
|
|
Navman F10 Mount with tilt swivel
Stock : 6
Item No. : 272005
£ 17.98 incl. Vat
Click Image to enlarge
The choice for you who want to have your device within easy reach, attached onto a ProClip instead of on the windshield suction mount. You can easily take the device with you when leaving the vehicle. The holder is equipped with a tilt swivel so it can be adjusted in order to avoid light reflection on the screen. Attach onto ProClip Mounting Platform.
|
|
Sony Ericsson Xperia X10 Passive Holder Tilt Swivel
Stock : 2
Item No. : 511137
£ 21.98 incl. Vat
Click Image to enlarge
When keeping your unit in a passive holder, it is always within easy reach. A portable handsfree or a charging cable can be connected to the unit when it is in the holder. The holder is attached onto a tilt swivel and can be adjusted in order to avoid light reflection. Attach onto a ProClip Mounting Platform.
|
|
